Part 1
요약·해설
Devicetree source path, sensor multiple-instance 제한과 2초 output을 보존합니다.
HTS221 · LPS22HB
LSM6DSL · LSM303AGR
Standard
Part 2
접을 수 있는 영어 원문 전체
영어 원문 전체 펼치기
1B412B32085CB5221BEB6016CDC05F3945B7C901DDE959FB517405FCCEC13E3C
.. zephyr:code-sample:: x-nucleo-iks01a2-std
:name: X-NUCLEO-IKS01A2 shield - Standard (Mode 1)
:relevant-api: sensor_interface
Interact with all the sensors of an X-NUCLEO-IKS01A2 shield using Standard Mode.
Overview
********
This sample enables all sensors of a X-NUCLEO-IKS01A2 shield, and then
periodically reads and displays data from the shield sensors:
- HTS221: Ambient temperature and relative humidity
- LPS22HB: Atmospheric pressure and ambient temperature
- LSM6DSL: 3-Axis Acceleration and 3-Axis Angular Velocity
- LSM303AGR 3-Axis Acceleration and 3-axis Magnetic field intensity
Requirements
************
This sample communicates over I2C with the X-NUCLEO-IKS01A2 shield
stacked on a board with an Arduino connector. The board's I2C must be
configured for the I2C Arduino connector in the devicetree. See for
example the :ref:`nucleo_f401re_board` board source code:
- :zephyr_file:`boards/st/nucleo_f401re/nucleo_f401re.dts`
- :zephyr_file:`boards/st/nucleo_f401re/arduino_r3_connector.dtsi`
Please note that this sample can't be used with boards already supporting
one of the sensors available on the shield (such as disco_l475_iot1) as zephyr
does not yet support sensors multiple instances.
References
**********
-X-NUCLEO-IKS01A2: https://www.st.com/en/ecosystems/x-nucleo-iks01a2.html
Building and Running
********************
This sample runs with X-NUCLEO-IKS01A2 stacked on any board with a matching
Arduino connector. For this example, we use a :ref:`nucleo_f401re_board` board.
.. zephyr-app-commands::
:zephyr-app: samples/shields/x_nucleo_iks01a2/standard
:board: nucleo_f401re
:goals: build
:compact:
Sample Output
=============
.. code-block:: console
X-NUCLEO-IKS01A2 sensor dashboard
HTS221: Temperature: 26.3 C
HTS221: Relative Humidity: 44.5%
LPS22HB: Pressure:99.220 kpa
LPS22HB: Temperature: 26.1 C
LSM6DSL: Accel (m.s-2): x: -0.0, y: -0.1, z: 10.0
LSM6DSL: Gyro (dps): x: 0.028, y: -0.025, z: 0.014
LSM303AGR: Accel (m.s-2): x: 0.3, y: -0.1, z: 9.7
LSM303AGR: Magn (gauss): x: -0.221, y: -0.042, z: -0.458
<updated endlessly every 2 seconds>
Part 3
한국어 전문 번역
개요
X-NUCLEO-IKS01A2 shield의 모든 sensor를 독립적으로 활성화한 뒤 주기적으로 읽어 표시하는 Standard mode sample입니다.
- HTS221: ambient temperature와 relative humidity
- LPS22HB: atmospheric pressure와 ambient temperature
- LSM6DSL: 3-axis acceleration과 3-axis angular velocity
- LSM303AGR: 3-axis acceleration과 3-axis magnetic field intensity
요구 사항
Arduino connector가 있는 board에 shield를 쌓고 I2C로 통신합니다. Board devicetree에서 Arduino connector용 I2C를 구성해야 합니다. 공식 예제 source path는 boards/st/nucleo_f401re/nucleo_f401re.dts와 boards/st/nucleo_f401re/arduino_r3_connector.dtsi입니다.
Zephyr 3.7.0은 sensor multiple instance를 지원하지 않으므로 disco_l475_iot1처럼 같은 sensor가 이미 있는 board에서는 이 sample을 사용할 수 없습니다.
참고 자료
빌드 및 실행
Matching Arduino connector가 있는 board에서 실행할 수 있으며, 아래 예제는 nucleo_f401re용입니다.
west build -b nucleo_f401re samples/shields/x_nucleo_iks01a2/standard
출력 예
X-NUCLEO-IKS01A2 sensor dashboard
HTS221: Temperature: 26.3 C
HTS221: Relative Humidity: 44.5%
LPS22HB: Pressure:99.220 kpa
LPS22HB: Temperature: 26.1 C
LSM6DSL: Accel (m.s-2): x: -0.0, y: -0.1, z: 10.0
LSM6DSL: Gyro (dps): x: 0.028, y: -0.025, z: 0.014
LSM303AGR: Accel (m.s-2): x: 0.3, y: -0.1, z: 9.7
LSM303AGR: Magn (gauss): x: -0.221, y: -0.042, z: -0.458
<updated endlessly every 2 seconds>
Temperature·humidity·pressure와 두 motion sensor의 acceleration, angular velocity, magnetic field 값을 한 dashboard에 표시하며 2초마다 계속 갱신합니다.
Source
출처
영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.