Part 1
요약·해설
두 board 요구 사항, TWR-KE18F build와 248-byte receive output을 보존합니다.
BS = 8 frames
STmin = 5 ms
2 CAN boards
Part 2
접을 수 있는 영어 원문 전체
영어 원문 전체 펼치기
33CA8819A4AB7CDCEB1AFA054D719F4ABE61FF7257B482F55F9A1F1BAD7352B5
.. zephyr:code-sample:: isotp
:name: ISO-TP library
:relevant-api: can_isotp
Use ISO-TP library to exchange messages between two boards.
Overview
********
This sample demonstrates how to use the :ref:`ISO-TP library <can_isotp>`.
Messages are exchanged between two boards. A long message, that is sent with
a block-size (BS) of eight frames, and a short one that has a minimal
separation-time (STmin) of five milliseconds.
The send function call for the short message is non-blocking, and the send
function call for the long message is blocking.
Building and Running
********************
Use these instructions with integrated CAN controller like in the NXP TWR-KE18F
or Nucleo-F746ZG board.
For the NXP TWR-KE18F board:
.. zephyr-app-commands::
:zephyr-app: samples/subsys/canbus/isotp
:board: twr_ke18f
:goals: build flash
Requirements
************
* Two boards with CAN bus support, connected together
Sample output
=============
.. code-block:: console
Start sending data
[00:00:00.000,000] <inf> can_driver: Init of CAN_1 done
========================================
| ____ ___ ____ ____ ____ |
| |_ _|/ __|| | ___ |_ _|| _ \ |
| _||_ \__ \| || | ___ || | ___/ |
| |____||___/|____| || |_| |
========================================
Got 248 bytes in total
This is the sample test for the short payload
TX complete cb [0]
.. note:: The values shown above might differ.
Part 3
한국어 전문 번역
개요
두 board 사이에서 message를 교환하며 ISO-TP library를 사용하는 방법을 보여 주는 sample입니다. 관련 API는 can_isotp입니다.
Long message는 block size(BS) 8 frame으로 보내고, short message는 minimum separation time(STmin) 5 ms로 보냅니다. BS는 receiver의 다음 flow-control을 기다리기 전에 연속으로 보낼 frame 수를 제한하고, STmin은 consecutive frame 사이 최소 간격을 정합니다.
Short message의 send function call은 non-blocking이라 전송 완료를 기다리지 않고 돌아오며, long message의 send function call은 blocking이라 전송 절차가 끝날 때까지 기다립니다.
빌드 및 실행
NXP TWR-KE18F 또는 Nucleo-F746ZG처럼 integrated CAN controller가 있는 board에서 이 절차를 사용합니다. 다음은 NXP TWR-KE18F용 build·flash command입니다.
# From the root of the zephyr repository
west build -b twr_ke18f samples/subsys/canbus/isotp
west flash
요구 사항
- CAN bus를 지원하고 서로 CAN wiring으로 연결된 board 두 대
출력 예
Start sending data
[00:00:00.000,000] <inf> can_driver: Init of CAN_1 done
========================================
| ____ ___ ____ ____ ____ |
| |_ _|/ __|| | ___ |_ _|| _ \ |
| _||_ \__ \| || | ___ || | ___/ |
| |____||___/|____| || |_| |
========================================
Got 248 bytes in total
This is the sample test for the short payload
TX complete cb [0]
CAN_1 initialization 뒤 248 byte long payload를 받은 결과와 short payload text, non-blocking transmission completion callback의 status 0을 확인할 수 있습니다. Timestamp와 실제 값은 실행마다 달라질 수 있습니다.
Source
출처
영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.