Part 1
요약·해설
Build+flash, 세 sensor route와 공식 output의 이름 불일치를 명시합니다.
LSM6DSV16X
LIS2MDL
LPS22DF
Part 2
접을 수 있는 영어 원문 전체
영어 원문 전체 펼치기
BF445797F5DAD5FAC4F5B705E3C5F5E6B29BD3A6E24A912739F2E7706D1456BF
.. _x-nucleo-iks4a1-shub1-sample:
X-NUCLEO-IKS4A1 shield SHUB1 (Mode 3) sample
############################################
Overview
********
This sample is provided as an example to test the X-NUCLEO-IKS4A1 shield
configured in SHUB1 (Mode 3).
Please refer to :ref:`x-nucleo-iks4a1-mode-3` for more info on this configuration.
This sample enables LSM6DSV16X IMU in sensorhub mode with LIS2MDL magnetometer and
LPS22DF pressure and temperature sensor.
Then sensor data are displayed periodically
- LSM6DSV16X 6-Axis acceleration and angular velocity
- LSM6DSV16X (from LIS2MDL) 3-Axis magnetic field intensity
- LSM6DSV16X (from LPS22DF) ambient temperature and atmospheric pressure
Requirements
************
This sample communicates over I2C with the X-NUCLEO-IKS4A1 shield
stacked on a board with an Arduino connector, e.g. the
:ref:`nucleo_f411re_board` board.
Building and Running
********************
This sample runs with X-NUCLEO-IKS4A1 stacked on any board with a matching
Arduino connector. For this example, we use a :ref:`nucleo_f411re_board` board.
.. zephyr-app-commands::
:zephyr-app: samples/shields/x_nucleo_iks4a1/sensorhub1/
:host-os: unix
:board: nucleo_f411re
:goals: build flash
:compact:
Sample Output
=============
.. code-block:: console
X-NUCLEO-IKS01A4 sensor dashboard
LSM6DSV16X: Accel (m.s-2): x: 0.081, y: -0.177, z: 9.945
LSM6DSV16X: GYro (dps): x: 0.001, y: -0.000, z: 0.004
LSM6DSV16X: Magn (gauss): x: 0.217, y: 0.015, z: -0.415
LSM6DSV16X: Temperature: 19.8 C
LSM6DSV16X: Pressure:99.655 kpa
16:: lsm6dso16is acc trig 6432
<updated endlessly every 2 seconds>
References
**********
:ref:`x-nucleo-iks4a1`
Part 3
한국어 전문 번역
개요
X-NUCLEO-IKS4A1 shield를 SHUB1(Mode 3)로 구성해 시험하는 sample입니다. 자세한 hardware configuration은 X-NUCLEO-IKS4A1 Mode 3 문서를 참조합니다.
LSM6DSV16X IMU를 sensor-hub mode로 활성화하고 LIS2MDL magnetometer와 LPS22DF pressure·temperature sensor를 연결합니다.
- LSM6DSV16X 자체의 6-axis acceleration과 angular velocity
- LIS2MDL에서 LSM6DSV16X를 거쳐 읽는 3-axis magnetic field intensity
- LPS22DF에서 LSM6DSV16X를 거쳐 읽는 ambient temperature와 atmospheric pressure
요구 사항
Arduino connector가 있는 board에 X-NUCLEO-IKS4A1 shield를 쌓고 I2C로 통신합니다. 예로 nucleo_f411re board를 사용할 수 있습니다.
빌드 및 실행
Matching Arduino connector가 있는 board에서 실행할 수 있으며, Unix host에서 nucleo_f411re용으로 build하고 flash하는 command입니다.
west build -b nucleo_f411re samples/shields/x_nucleo_iks4a1/sensorhub1/
west flash
출력 예
X-NUCLEO-IKS01A4 sensor dashboard
LSM6DSV16X: Accel (m.s-2): x: 0.081, y: -0.177, z: 9.945
LSM6DSV16X: GYro (dps): x: 0.001, y: -0.000, z: 0.004
LSM6DSV16X: Magn (gauss): x: 0.217, y: 0.015, z: -0.415
LSM6DSV16X: Temperature: 19.8 C
LSM6DSV16X: Pressure:99.655 kpa
16:: lsm6dso16is acc trig 6432
<updated endlessly every 2 seconds>
LSM6DSV16X가 자체 acceleration·gyroscope와 두 external slave의 magnetic field·temperature·pressure를 합쳐 표시하며 2초마다 갱신합니다. 공식 output title의 IKS01A4, GYro, trigger label의 lsm6dso16is는 문서명·device명과 다르지만 exact source를 보존했습니다.
참고 자료
X-NUCLEO-IKS4A1 shield 문서를 참조하십시오.
Source
출처
영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.