samples/sensor/th02/README.html · samples/sensor/th02/README.rst 공식 원문 ↗

Zephyr 3.7.0 · Samples · Sensor · Grove

TH02 temperature·humidity monitor

Grove shield에서 TH02를 읽어 temperature와 humidity를 5 V LCD에 표시합니다.

Official pathsamples/sensor/th02/README.html
Source filesamples/sensor/th02/README.rst
Source versionZephyr 3.7.0
TranslationFull · reviewed

본문 기준: Zephyr 3.7.0 LTS3 · 이후 유지보수 패치는 별도입니다.

Part 1

요약·해설

두 device, 10 kΩ pull-up 가능성, 5 V switch와 reference를 설명합니다.

Sensor

TH02 · Si7005

Display

Grove LCD

Bus

I2C

Part 2

접을 수 있는 영어 원문 전체

영어 원문 전체 펼치기
원문 SHA-256 B0D9A65310431B648518FF0342676E2A2716D5AED2FE9C89DB3985BA60D20BEA
.. _th02-sample:

TH02: Temperature and Humidity Monitor
######################################

Overview
********
This sample periodically reads temperature and humidity from the Grove
Temperature & Humidity Sensor (TH02) and display the results on the Grove LCD
display.


Requirements
************

This sample uses the TH02 sensor and the grove LCD display. Both devices are
controlled using the I2C interface.

More details about the sensor and the display can be found here:

- `Grove Temperature And Humidity`_
- `Grove LCD Module`_

Wiring
******

The easiest way to get this wired is to use the Grove shield and connect both
devices to I2C. No additional wiring is required. Depending on the board you are
using you might need to connect two 10K ohm resistors to SDL and SDA (I2C).
The LCD display requires 5 volts, so the voltage switch on the shield needs to
be on 5v.


References
**********

 - TH02 (Si7005): https://www.silabs.com/documents/public/data-sheets/Si7005.pdf


.. _Grove LCD Module: http://wiki.seeed.cc/Grove-LCD_RGB_Backlight/
.. _Grove Temperature And Humidity: http://wiki.seeed.cc/Grove-TemptureAndHumidity_Sensor-High-Accuracy_AndMini-v1.0/

Part 3

한국어 전문 번역

개요

이 sample은 Grove Temperature & Humidity Sensor(TH02)에서 temperature와 humidity를 주기적으로 읽어 Grove LCD display에 결과를 표시합니다.

요구 사항

이 sample은 TH02 sensor와 Grove LCD display를 사용하며 두 device 모두 I2C interface로 제어합니다.

자세한 내용은 Grove Temperature and Humidity 및 Grove LCD Module 문서를 참조하십시오.

배선

가장 쉬운 방법은 Grove shield를 사용해 두 device를 모두 I2C에 연결하는 것입니다. 추가 배선은 필요하지 않습니다. Board에 따라 SCL·SDA에 10 kΩ resistor 두 개를 연결해야 할 수 있습니다. 공식 원문에는 SCL이 SDL로 표기되어 있습니다.

LCD display에는 5 V가 필요하므로 shield의 voltage switch를 5 V 위치에 두어야 합니다.

참고 자료

Source

출처

영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.